William Hedley Locomotive Pioneer

SUBJECT AREA: Land transport, Mining and extraction technology, Railways and locomotives

[br]

[br]

[br]

The Wylam wagonway passed Newburn, and Hedley, who went to school at Wylam, must have been familiar with this wagonway from childhood. It had been built c.1748 to carry coal from Wylam Colliery to the navigable limit of the Tyne at Lemington. In 1805 Hedley was appointed viewer, or manager, of Wylam Colliery by Christopher Blackett, who had inherited the colliery and wagonway in 1800. Unlike most Tyneside wagonways, the gradient of the Wylam line was insufficient for loaded wagons to run down by gravity and they had to be hauled by horses. Blackett had a locomotive, of the type designed by Richard Trevithick, built at Gateshead as early as 1804 but did not take delivery, probably because his wooden track was not strong enough. In 1808 Blackett and Hedley relaid the wagonway with plate rails of the type promoted by Benjamin Outram, and in 1812, following successful introduction of locomotives at Middleton by John Blenkinsop, Blackett asked Hedley to investigate the feasibility of locomotives at Wylam. The expense of re-laying with rack rails was unwelcome, and Hedley experimented to find out the relationship between the weight of a locomotive and the load it could move relying on its adhesion weight alone. He used first a model test carriage, which survives at the Science Museum, London, and then used a full-sized test carriage laden with weights in varying quantities and propelled by men turning handles. Having apparently satisfied himself on this point, he had a locomotive incorporating the frames and wheels of the test carriage built. The work was done at Wylam by Thomas Waters, who was familiar with the 1804 locomotive, Timothy Hackworth, foreman smith, and Jonathan Forster, enginewright. This locomotive, with cast-iron boiler and single cylinder, was unsatisfactory: Hackworth and Forster then built another locomotive to Hedley's design, with a wrought-iron return-tube boiler, two vertical external cylinders and drive via overhead beams through pinions to the two axles. This locomotive probably came into use in the spring of 1814: it performed well and further examples of the type were built. Their axle loading, however, was too great for the track and from about 1815 each locomotive was mounted on two four-wheeled bogies, the bogie having recently been invented by William Chapman. Hedley eventually left Wylam in 1827 to devote himself to other colliery interests. He supported the construction of the Clarence Railway, opened in 1833, and sent his coal over it in trains hauled by his own locomotives. Two of his Wylam locomotives survive— Puffing Billy at the Science Museum, London, and Wylam Dilly at the Royal Museum of Scotland, Edinburgh—though how much of these is original and how much dates from the period 1827–32, when the Wylam line was re-laid with edge rails and the locomotives reverted to four wheels (with flanges), is a matter of mild controversy.

[br]

See also: Stephenson, George

SUBJECT AREA: Land transport, Railways and locomotives

[br]

[br]

[br]

Hackworth trained under his father, who was Foreman Blacksmith at Wylam colliery, and succeeded him upon his death in 1807. Between 1812 and 1816 he helped to build and maintain the Wylam locomotives under William Hedley. He then moved to Walbottle colliery, but during 1824 he took temporary charge of Robert Stephenson \& Co.'s works while George Stephenson was surveying the Liverpool \& Manchester Railway and Robert Stephenson was away in South America. In May 1825 Hackworth was appointed to the Stockton \& Darlington Railway (S \& DR) "to have superintendence of the permanent (i.e. stationary) and locomotive engines". He established the workshops at Shildon, and when the railway opened in September he became in effect the first locomotive superintendent of a railway company. From experience of operating Robert Stephenson \& Co.'s locomotives he was able to make many detail improvements, notably spring safety valves. In 1827 he designed and built the locomotive Royal George, with six wheels coupled and inverted vertical cylinders driving the rear pair. From the pistons, drive was direct by way of piston rods and connecting rods to crankpins on the wheels, the first instance of the use of this layout on a locomotive. Royal George was the most powerful and satisfactory locomotive on the S \& DR to date and was the forerunner of Hackworth's type of heavy-goods locomotive, which was built until the mid-1840s.

For the Rainhill Trials in 1829 Hackworth built and entered the locomotive Sans Pareil, which was subsequently used on the Bol ton \& Leigh Railway and is now in the Science Museum, London. A working replica was built for the 150th anniversary of the Liverpool \& Manchester Railway in 1980. In 1833 a further agreement with the S \& DR enabled Hackworth, while remaining in charge of their locomotives, to set up a locomotive and engineering works on his own account. Its products eventually included locomotives for the London, Brighton \& South Coast and York, Newcastle \& Berwick Railways, as well as some of the earliest locomotives exported to Russia and Canada. Hackworth's son, John Wesley Hackworth, was also an engineer and invented the radial valve gear for steam engines that bears his name.

[br]